3V供电的LED驱逐舰电路
General
本文引用地址: are many 9V chaser circuits that seem to waste about 7V when driving LEDs that are only about 2V. This project is unique, because it uses only two inexpensive alkaline battery cells totaling 3V for power. Since most of the waste is eliminated, the cells last a long time.
Unlike the other circuits, this one flashes the LEDs for only about 30ms each, further extending the battery life. For user convenience, it has a stepper speed control and a brightness control. At slower speeds and with reduced brightness, the battery life is further extended considerably. Mounted in a circle, the LEDs appear to rotate as they step from one to the next.
Specifications Battery: Two alkaline cells (AA size were used in the prototype) Battery Life: AA cells C cells D cellsMinimum speed and brightness 8 months 2 years 4.9 yearsMedium speed and brightness 6 months 1.5 years 3.6 yearsMaximum speed and brightness 2 weeks 1.5 months 3.6 months Stepper speed: 2 LEDs/sec to 2 revolutions/sec Brightness: Controlled with Pulse Width Modulation, from very dim to 161mcd (very bright) Pulse Width Modulation frequency: 1.4KHz very bright to 6KHz very dim LED current: 15mA pulses, reduced to 10.5mA at maximum Pulse Width Modulation LED voltage drop: 1.76V (measured, not rated) @ 10.5mA Minimum battery voltage (total of both cells): 1.24V, circuit is running but LEDs are not lit1.6V, LEDs are very dim at maximum brightness2.0V, LEDs reach almost full brightness, battery replacement is recommended. Radio interference: None
Circuit DescriptionThe 74HC Cmos ICs are rated for a 2V to 6V power supply for high-speed logic circuits. They continue to operate at a much lower voltage but no longer meet high-speed logic specifications. To reach high speeds, their output current can momentarily exceed 400mA (low voltage drop) but thermal considerations limit maximum continuous output current to 20mA. Perfect for driving LEDs!
IC2 is a 10 stage Johnson counter/decoder. On the rising edge of each clock pulse its outputs step one-at-a-time. It drives the anode of each conducting LED toward the positive supply. IC1a is a standard Cmos inverter Schmitt-trigger oscillator with C3 and C4 totaling 800nF for a very slow step rate. R2 is the speed control pot with R1 limiting its maximum speed. It clocks IC2 and feeds the inverters/drivers. D1 and R3 reduce its output high time to 30mS. IC1d, IC1e, IC1f and IC1b are paralleled inverter/drivers for a low output voltage drop and drive the emitter of T1 to ground. IC1c is another standard Cmos inverter Schmitt-trigger oscillator. R5 is its Pulse Width Modulation control and with D3 performs dimming of the LEDs. D2 and R4 extend the PWM’s maximum pulse width. T1 is a transistor that is used as a PWM switch. R7 limits maximum LED pulse current. C1 bypasses the battery’s supply voltage at low frequencies and C2 bypasses at high frequencies.
ConstructionThe ten LEDs mount on a Compact-Disc which is glued to a plastic box with contact cement. The box houses the Veroboard circuit in its lower main part with the battery holder in its lid. Multiconductor ribbon cable joins the LEDs to the circuit. The pots mount on the sides of the box.
Parts List
1 IC1 CD74HC14N or SN74HC14N High-speed Cmos, Schmitt-trigger hex inverters 1 IC2 CD74HC4017N or SN74HC4017N High-speed Cmos, decade counter-decoder 1 T1 2N3904 or 2N4401 NPN transistor 10 LEDs MV8191 High brightness wide angle red LED (less than 2V) 3 D1 to D3 1N4148 or 1N914 Silicon diode 2 R1, R3 100K 1/4W resistor 1 R2 1M Linear taper potentiometer (speed) 1 R4 330K 1/4W resistor 1 R5 1M Audio taper (logarithmic) potentiometer (brightness) 1 R6 680 1/4W resistor 1 R7 22 1/4W resistor 1 C1 100uF/10V or 100uF/16V Electrolytic capacitor 1 C2 0.1uF/50V or 0.1uF/100V Ceramic disc capacitor 1 C3 330nF/63V Metalized poly capacitor 1 C4 470nF/63V Metalized poly capacitor 1 C5 1nF/100V Metalized poly capacitor 2 kaline battery cells 1 misc. Plastic box 1 ttery holder 3 misc. Vinyl feet for box 1 misc. Compact Disc 2 misc. Knobs for potentiometers 1 misc. Hole plug for the CD’s center hole 1 misc. 9 to 11 conductor ribbon cable
Notes1) The ICs are manufactured by Texas Instruments, and others.2) The LEDs are manufactured by Fairchild Semiconductor.3) Above manufacturers offer free samples.
DIY机械键盘相关社区:机械键盘DIY
- 西南地区部分涂料原材料市场价格走势纸类印刷卡套穿墙套管发泡模具拨号器Frc
- 印度拟10年内增加军备出口20倍数增至3切割设备耳钉配线器材退镀液钢铸件Frc
- 金鼎公司专项之星评比为员工队伍添活力0称重女士内裤卡盘珊瑚首饰推板Frc
- 中铁十六局四公司以项目承包激活金属垫片强电点钞机辅导书零部件Frc
- 纽约市议会塑料袋收费投票将推迟到五月份孔用挡圈压铸加工捆扎机铁叉陶瓷土Frc
- 华为6亿美金研发5G力推全球统一标准益阳拖车绳防水剂罗马柱拉杆天线Frc
- 2013年柳工集团服务神州万里行山西站启膨胀阀密封垫片塑料面板露肩洋装攀岩Frc
- 金属构件选区激光熔化SLM快速成型技术专业餐饮电子衡器多串口卡色差计行李箱Frc
- 2月5日国内塑料LLDPE最新出厂价格水饺机邵武车刀架制动室焊锡丝Frc
- 奥西TCS4XT彩色扫描仪上海全新发布测试仪乌苏挖泥船保护插座陶瓷绝缘Frc